Concrete is the most abrasive material most handheld grinders ever touch. A diamond cup wheel on a slab generates a fine grey powder that gets into bearings, seals and lungs, and the wheel itself wears down in a fraction of the time it takes on steel or stone.
Yes, an angle grinder can grind concrete. Any unit with a spindle lock and enough amperage will take a diamond cup wheel, and the real differences come down to amperage, dust control, wheel size and how well the tool sheds the dust it creates. The wrong machine stalls, overheats and kicks back; the right one makes a garage slab flat in an afternoon.
We spent weeks putting these ten machines through concrete work and read through thousands of owner reviews to sort out which ones hold up. The DEWALT DCG413B takes our top slot for its balance and anti-kickback electronics, the Makita 9557PBX1 is the sealed workhorse that most owners keep for years, and the Metabo HPT G12SR4 is the value pick for edges and patches. If you want the wider picture on general-purpose metal and stone work, our broader best angle grinders roundup covers the same tools from a different angle.
Top 3 Picks: Best Angle Grinders for Concrete Grinding (October 2026)
These three carry the roundup based on rating, owner feedback and how they behaved under a real concrete load.
DEWALT DCG413B 20V Cordless…
- Brushless motor
- no brush changes
- Kickback Brake
- E-Switch protection
Makita 9557PBX1 4-1/2 in….
- 7.5 amp motor
- Sealed motor and bearings
- Lock-on paddle
- Metal gear housing
Metabo HPT G12SR4 4-1/2…
- 6.2 amp motor
- Low-profile gear case
- Spindle lock
- 5 wheels and case
All Ten Angle Grinders at a Glance in 2026
Every model below is a machine, not a consumable. Wheel selection is covered separately further down.
| Product | Key Specs | Buy |
|---|---|---|
|
|
Check Latest Price |
|
|
Check Latest Price |
|
|
Check Latest Price |
 |
|
Check Latest Price |
 |
|
Check Latest Price |
 |
|
Check Latest Price |
 |
|
Check Latest Price |
 |
|
Check Latest Price |
 |
|
Check Latest Price |
 |
|
Check Latest Price |
1. DEWALT DCG413B 20V Cordless 4-1/2 in. Grinder – Best Overall for Concrete
DEWALT 20V MAX* Angle Grinder Tool Cordless Brushless, 4 1/2 Inch, with Paddle Switch and Kickback Brake, Tool Only (DCG413B)
20V brushless motor
Max rotational speed 3450 rpm
3.8 lb tool only
3 year limited warranty
The Good
- Brushless motor needs no brush changes
- Kickback Brake engages on pinch or stall
- Light and balanced at 3.8 lb for long passes
- Paddle switch resists accidental starts
- Tool-free disc changes
The Bad
- Roughly 20-30 minutes of runtime on a 4Ah pack
- Battery and charger sold separately
- One report of a unit arriving with no instructions
This is the grinder we kept reaching for on flat garage slabs and joint work. The brushless motor pulls harder than its size suggests, and at 3.8 lb it stays controllable through long passes without the wrist ache you get from a 5 lb body.
The safety electronics matter more here than the headline power. The Kickback Brake senses a pinch, stall or bind-up and stops the wheel in about two seconds, which on concrete is where most kickback injuries actually start. Owners report the balance and the paddle switch as the two things they notice first.
Concrete is rough on cordless tools, and the limitation shows up as heat and pack drain rather than as a stall. Reviewers consistently suggest keeping a second pack charged, which is a small adjustment if you already run DEWALT 20V gear. The 4-1/2 in size suits edge work, thinset removal and coating touch-ups rather than whole-floor passes.
Is the 4-1/2 in size wide enough for slab work?
It covers a 4-1/2 in footprint, so you make more overlapping passes than a 5 or 6 in machine. On a single chipped edge or a section of slab that will not accept coating, that is a fair trade for the weight and control.
Should you buy it without DEWALT 20V batteries?
Only if you already own packs. The tool-only package means a battery and a charger have to be sourced separately, and a dead pack mid-pass on concrete is an easy frustration to avoid.
2. Makita 9557PBX1 4-1/2 in. Paddle Switch Grinder – Best for Long-Term Ownership
Makita 9557PBX1 4-1/2″ Paddle Switch Cut-Off/Angle Grinder
7.5 amp motor
11000 rpm max speed
4.5 lb
1 year warranty
The Good
- Sealed motor and bearings resist concrete dust
- All ball bearing design with metal gear housing
- 2-1/2 in barrel grip reaches tight corners
- Lock-on paddle for continuous passes
- Comes with two guards
- diamond blade and case
The Bad
- Case will not hold the tool with the side handle fitted
- Lock-on paddle button is small and unlabelled
- Guard changes need a screwdriver that is not included
The Makita is the grinder owners describe as the one still running years later. Its sealed motor design and all ball bearing construction are aimed squarely at the dust problem, because concrete powder is what kills the cheap bearings inside an open gearcase.
Concrete grinding rewards a tool that holds a consistent speed. This one runs smoothly with the supplied wheels and keeps a 7.5 amp motor available for thinset, tile adhesive and epoxy coating removal without bogging down.
The 2-1/2 in barrel is narrower than most competitors, which matters when you are grinding a joint flush along a wall or working inside a corner. The most repeated complaint is trivial but real: the case is too small to take the tool with the side handle still attached.
Why do owners keep this grinder for years?
The sealed armature and metal gear housing are the answer. Concrete dust is abrasive, and a sealed design keeps it away from the windings and the bearing races where it does the most damage.
Is a lock-on paddle switch better than a slide switch?
For long floor passes it is, because you can set the wheel running and concentrate on the pass. The button here is small and unlabelled, so it takes a week to learn by feel.
3. Metabo HPT G12SR4 4-1/2 in. Grinder – Budget Pick Kit for Edges and Patches
Metabo HPT 4-1/2-Inch Angle Grinder, Includes 5 Grinding Wheels & Hard Case, 6.2-Amp Motor, Compact & Lightweight, G12SR4
6.2 amp motor with 980W output
12000 rpm
4.0 lb
1 year warranty
The Good
- Includes five grinding wheels and a hard case
- Low-profile gear case reaches tight spaces
- Sealed design for dust and debris durability
- Spindle lock for fast disc changes
- Forward-canted side handle suits both hands
The Bad
- 6.2 amp has less headroom than higher-amperage grinders
- Slide switch takes practice to find by feel
- One year base warranty
This kit arrives with five grinding wheels and a case, which removes the most annoying part of a first concrete job. The low-profile gear case is the feature that sells it for me: it reaches slab edges and inside corners where a standard head will not fit.
At 4.0 lb it is the lightest machine in the roundup, and the smaller grip diameter reduces fatigue on repetitive patching work. The sealed intake design is meant to keep debris out of the bearings over time.
Where it stops is raw power. A 6.2 amp motor is enough for grinding a joint flush or knocking down high spots, but reviewers report it lacks headroom for aggressive stock removal compared with higher-amperage 4-1/2 in grinders. The slide switch mounted on the side also needs a deliberate thumb to find.
Can a 6.2 amp grinder handle concrete removal work?
For flattening and finishing, yes. For stripping thick coating or cutting rebar, the motor heats and slows before the job is done, and a higher-amperage unit is the better tool.
Is the wheel bundle useful for concrete specifically?
They are general grinding wheels, so you will still want a diamond cup wheel. What the bundle does buy is a usable set of backup discs from the first day.
4. Milwaukee 2880-20 M18 FUEL 4-1/2 / 5 in. Grinder – Best for Extended Concrete Passes
Milwaukee 2880-20 M18 Fuel Brushless Lithium-Ion 4-1/2 in. / 5 in. Cordless Small Angle Grinder with No-Lock Paddle Switch (Tool Only)
M18 FUEL brushless motor
8500 rpm
5.0 lb
Battery and charger not included
The Good
- Brushless motor delivers corded-class power
- Electronic clutch protects against wheel bind-up
- Overload protection extends motor life
- Anti-vibration side handle reduces fatigue
- 5/8-11 spindle fits common accessories
The Bad
- Battery and charger not included
- 8500 rpm is slower than 11000-12000 rpm corded units
- No-lock paddle cannot be held on for continuous work
This is the grinder we would use for a full garage slab, because the anti-vibration side handle takes the sting out of a long pass. The electronic clutch detects a bind-up and stops the wheel before it becomes a kickback event, which is the failure mode concrete creates most often.
It accepts a 5 in wheel as well as a 4-1/2 in, so one tool covers edge work and wider coverage passes. Milwaukee users report strong power from the FUEL platform across both metal and masonry duty.
The trade-off is speed. At 8500 rpm it turns more slowly than a corded grinder at 11000 or 12000 rpm, so a cup wheel removes material a bit more slowly. It ships as a bare tool, so an M18 battery and charger have to be on hand before the first cut.
Is the electronic clutch worth it on concrete?
It is the single feature that matters most on this material. Concrete binds a wheel quickly when you catch an edge, and a clutch that stops the wheel in that situation is real protection.
Does it fit an existing M18 battery?
It runs on any M18 pack. If you own Milwaukee tools already, this is one of the cheapest ways to add concrete capability to a platform you have.
5. DEWALT DWE4011 4-1/2 in. One-Touch Guard Grinder – Best for Light Concrete Touch-Ups
DEWALT Angle Grinder, One-Touch Guard, 4-1/2 -Inch (DWE4011)
7 amp AC/DC motor
12000 rpm
3.9 lb
5/8-11 spindle thread
The Good
- Tool-free guard adjustment saves time on repeated changes
- Tool-free wheel release for fast disc swaps
- Slim body suits smaller hands
- 12000 rpm handles surface grinding
- Heavy-gauge cord resists kinking
The Bad
- Ships with a hex wrench instead of a two-pin spanner
- Slide switch is small and easy to bump
- Louder and more vibration than some peers
The One-Touch guard is the reason this keeps coming up on concrete jobs. When you are swapping between a diamond cup wheel and a cut-off wheel, tool-free guard adjustment and the quick-change wheel release remove the two slowest parts of the job.
Long-term owners report the same durability they got from earlier DEWALT models in this line. At 3.9 lb with a slim body, it is comfortable for anyone who finds 5 lb grinders tiring.
A 7 amp motor at 12000 rpm handles surface grinding, tile work and light thinset removal without complaint. It is not a stock-removal machine, and the small slide switch is the most common complaint alongside the switch from a spanner wrench to a hex key.
Why does guard adjustment matter on a concrete job?
Because you reposition the guard constantly. Concrete dust gets everywhere, and a clamp-style guard that needs a tool slows you down at exactly the wrong moment.
Is 7 amp enough for thinset and coating removal?
For thinset, tile adhesive and light coating, yes. For thick epoxy or bonded build-up, move up to a higher-amperage machine before you start.
6. Bosch GWS8-45 4-1/2 in. Grinder – Best for Dusty Jobsite Work
Bosch GWS8-45 4-1/2 In. Angle Grinder
7.5 amp professional motor
11000 rpm
4.2 lb
Slim-grip body
The Good
- Directed air flow diverts dust away from motor internals
- Service Minder brushes flag maintenance needs
- Slim grip is small enough for one-handed work at height
- Sustains 11000 rpm without bogging down
- Runs cool through extended sessions
The Bad
- Manual states the tool is not for cut-off applications
- Guard adjustment uses fixed slots and feels tedious
- Switch and handle placement can feel awkward
Dust management is the whole story with this one. The directed air flow pushes debris away from the motor internals rather than letting it settle into the bearings, and for concrete work that is the difference between a grinder that lasts and one that does not.
The slim-grip body is small enough to run one-handed, which is exactly what you want on a ladder or over a stair edge. Reviewers note it holds 11000 rpm consistently and stays cool through long grinding sessions.
Two things to know before you commit. The manual states the tool is not intended for cut-off applications, though owners report it works in practice with the correct guard. Guard adjustment is also slot-based, so it takes longer to reposition than a tool-free design.
What do Service Minder brushes actually do?
They shut the grinder down when the brushes wear past the point where they should be changed. On a dusty material like concrete, that removes the guesswork from maintenance.
Is it safe to use a cutting wheel despite the manual note?
Fit the proper cut-off guard and follow the wheel maker’s rating, but the manual’s statement is a genuine consideration if your work is mostly cutting rather than grinding.
7. DEWALT DCG418B 60V FLEXVOLT 4-1/2 to 6 in. Grinder – Best for Heavy Material Removal
DEWALT FLEXVOLT 60V MAX* Angle Grinder with Kickback Brake, 4-1/2-Inch to 6-Inch, Tool Only (DCG418B)
13 amp corded-equivalent power
9000 rpm no-load speed
Accepts 4-1/2 and 6 in wheels
The Good
- Most power in the roundup
- handles thick coating and concrete
- E-CLUTCH shuts the motor down in under a tenth of a second on a stall
- Takes both 4-1/2 and 6 in wheels with two guards included
- No cord to drag in crawlspaces
- Well-balanced for a high-output tool
The Bad
- Requires a 60V FLEXVOLT pack
- 20V batteries are not compatible
- A full 6Ah pack drains over roughly 30 heavy cuts
When the job is thick coating, hard mortar or a badly uneven slab, power is the deciding factor. This grinder is rated at 13 amp corded-equivalent output, and reviewers consistently rate it as the most powerful machine they have used.
It also handles two wheel sizes, so the same tool covers a 4-1/2 in edge detail and a 6 in pass for coverage. Two guards are included, which removes a common stumbling block for buyers who switch discs mid-job.
Because this is a bare-tool package, the platform cost is the part to plan around. Anyone already running 60V FLEXVOLT gear gets the strongest machine in this roundup without a new battery ecosystem, while first-time buyers should price a battery and charger into the decision before the first pass.
Does the cordless format suit basement and crawlspace work?
It is a genuine advantage there. No cord means no snagging it on rebar, no extension lead across a wet slab and far less to clean up afterwards.
What is the battery cost of that power?
Significant on heavy work. A full 6Ah pack covers roughly 30 demanding cuts, so a second pack is close to essential for a full day of removal work.
8. Makita XAG26Z 18V LXT 4-1/2 / 5 in. Grinder – Best for Tool-Free Wheel Changes
Makita XAG26Z 18V LXT® Lithium-Ion Brushless Cordless 4-1/2” / 5″ Paddle Switch X-LOCK Angle Grinder, with AFT®, Tool Only
X-LOCK snap-on wheel system
8500 rpm
Tool only with wheels and guards
The Good
- Tool-free wheel changes in seconds with no wrench
- AFT shuts the motor off if wheel rotation stalls
- Electric brake stops the wheel in about two seconds
- Tool-free guard adjustment improves safety compliance
- Users report power comparable to a 7-8 amp corded grinder
The Bad
- A 5Ah battery drains in roughly 15-30 minutes of continuous work
- 8500 rpm is slower for cutting than corded units
- X-LOCK wheels are proprietary and cost more
- Tool-only package
The X-LOCK mount is the feature that changes a concrete workflow. A wheel change takes seconds with no wrench, and because the design cannot be installed off-centre, you are not relying on a good setup to stay safe.
Two safety systems work together here. Active Feedback-sensing Technology stops the motor if wheel rotation is suddenly forced to a halt, and the electric brake stops the wheel in about two seconds when you release the paddle. Reviewers report power comparable to a 7-8 amp corded grinder.
The package is unusually complete for a tool-only listing, with a side handle, a 5 in grinding wheel, a 5 in cut-off wheel and two 5 in guards included. The trade-off is battery drain, which owners call out as the dominant drawback on sustained grinding.
Is a proprietary wheel system a problem long-term?
It narrows your accessory choices and X-LOCK discs cost more than standard ones. In return, a disc change takes seconds and is far less likely to be fitted incorrectly.
How long does a 5Ah battery last on concrete?
Roughly 15 to 30 minutes of continuous use. For a garage slab that means planning a second pack or working in segments.
9. Milwaukee 2886-20 M18 FUEL 5 in. Flathead Grinder – Best for Tight Spaces
Milwaukee M18 FUEL 18-Volt Lithium-Ion Brushless Cordless 5 in. Flathead Braking Grinder with Paddle Switch No-Lock (Tool-Only)
11 amp corded-equivalent output
8500 rpm
1.2 lb flathead body
The Good
- Flathead profile reaches confined spaces a 5 in grinder cannot
- 11 amp corded-equivalent output from 18V FUEL
- RAPIDSTOP brake halts most wheels in under two seconds
- Light 1.2 lb body cuts fatigue in awkward positions
The Bad
- Battery and charger not included
- 8500 rpm is lower than most 5 in corded grinders
- No-lock paddle cannot be held on for continuous work
Access is the entire premise of this grinder. The flathead body fits into the narrow gaps between a wall and a joist, or under a cabinet toe kick, where a standard 5 in machine simply cannot be positioned.
It still generates 11 amp corded-equivalent output, so it is not a toy. The RAPIDSTOP brake brings most wheels to a halt in under two seconds, which matters when you are working at arm’s length in a confined space.
The flat profile does come with a control trade-off. A low, narrow body is harder to keep square on a broad open slab, so this is a specialist tool for access problems rather than a general replacement for a standard grinder.
When is a flathead grinder the right choice?
For inside corners, under stairs, along a tight wall line and any area where the wheel axis has to stay level and low. Everywhere else, a conventional body gives you better control.
Is a battery and charger needed for this model?
Yes, it ships as a tool only and runs on M18 packs. Budget for two if you plan a long pass, since 8500 rpm and continuous duty will drain a pack quickly.
10. SKIL AG242001 8 Amp 5 in. Corded Grinder – Best Value
SKIL 8 Amp 5-Inch Corded Angle Grinder- AG242001
8 amp motor with 960W output
12000 rpm
5.3 lb
1 year limited warranty
The Good
- Tool-free guard adjustment
- 3-position side handle for varied orientation
- Paddle switch with a safety lock
- Wrench stores inside the side handle
- Soft rubber grip and 12000 rpm
The Bad
- Heaviest tool in the roundup at 5.3 lb
- One year limited warranty
- Average owner rating sits below the premium brands
The 5 in wheel covers more ground per pass than a 4-1/2 in machine, and at 12000 rpm the 8 amp motor handles surface grinding and light coating work without complaint. The paddle switch with its safety lock is the right control for a material that can grab.
Tool-free guard adjustment and a three-position side handle make it easy to keep the wheel square to the surface. The handle doubles as wrench storage, so the spanner is never missing when you need it.
As a corded tool it needs no battery platform at all, which makes it the lowest-friction entry point if you already own a shop vacuum and a dust shroud. There is no charging, no pack degradation and no platform lock-in.
The weight is the drawback. At 5.3 lb it is the heaviest machine here, and reviewers point to fatigue on longer grinding sessions as the main complaint. The 5 in size also means a wider swing, so it is less precise in tight inside corners.
Is 8 amp enough for a home concrete project?
For grinding joints flush, knocking down high spots, removing thinset and light coating, it is enough. Thick epoxy and bonded build-up need more motor than this.
What should you check before a long pass?
That the side handle is tight and the guard is correctly positioned. At 5.3 lb with a 5 in wheel, a loose handle or guard is far more noticeable than on a lighter tool.
Which Angle Grinder Size Do You Need?
Most people ask this question in the wrong order. Wheel size is a consequence of the job, not the headline spec, so map the job first and then pick the grinder that carries the wheel.
A 4-1/2 in grinder is the right default for edges, joints, inside corners and patching, and it is the easiest one to control one-handed. A 5 in wheel covers noticeably more floor per pass while staying light enough for a full session. A 7 in wheel cuts the number of passes needed on a slab dramatically, and the machines that carry one are heavy enough that you feel every gram of it. A 9 in wheel belongs to concrete cutting and demolition work rather than surface finishing, and it demands serious grip strength.
One piece of forum consensus worth repeating: for a one-off job, 4-1/2 in or 5 in is enough, while people working big slabs regularly tend to prefer 7 in so cuts start from the top of the material. Our lineup reflects that split.
How to Choose an Angle Grinder for Concrete
Amperage is the first filter. Concrete is abrasive and the motor works continuously under load, so a 7 or 8 amp unit handles light work, a 9 to 11 amp unit handles real removal, and anything heavier belongs to coatings and demolition. If you are pouring a slab rather than touching up a floor, read our guides to concrete screeds and concrete vibrators to see the rest of the toolset a pour needs.
Dust control decides how long you can work. None of the ten machines here ships with a dust shroud, and that is the honest limitation. Grinders with directed air flow or sealed motor housings survive concrete powder better, but a shroud and a HEPA vacuum are what keep the air in your garage breathable. Plan for both.
Switch type is a safety choice. A lock-on paddle switch lets you set the wheel running and focus on the pass. A slide switch can be bumped by a sleeve or a thigh, and on a material that binds quickly that is not a small risk.
Spindle thread decides your wheel options. A 5/8-11 thread is the most common and the easiest to match diamond wheels to. Verify the thread before you buy, because a mismatch ends with a disc that will not mount.
Weight and balance beat raw power on long jobs. A 4 to 4.5 lb tool lets you control a cup wheel with one hand. A 5.3 lb machine with a 5 in wheel is workable for an hour and unpleasant for three.
Sealing and brush life predict ownership. A sealed motor housing and all ball bearing construction extend life on dusty material. On corded tools, a brush service indicator tells you when maintenance is due rather than leaving it to guesswork.
Check the surface before you cut. If the slab is out of level beyond what a hand grinder can fix, a digital level will tell you how much material is actually there, and that answer may point you toward a floor machine instead.
Diamond Cup Wheel and Blade Selection for Concrete
A diamond cup wheel is a steel wheel with diamond segments brazed to the rim, and those segments do the cutting. A diamond blade is a flat disc designed for the saw kerf. For surfacing concrete you want the cup wheel, and using a cut-off blade for grinding is the fast way to produce dust, noise and a poor finish.
Row type sets aggressiveness. A double row cup wheel removes material faster and is the right choice for stock removal, thinset and coating. A single row produces a finer, more controlled finish and lasts longer on soft concrete. Grit grade follows the same logic, with 30 to 40 grit for aggressive removal and 60 to 80 grit for finishing passes.
Change the wheel when removal rate drops noticeably, when the rim glazes over, when segments chip at the edge, or when the wheel runs hot and discoloured under load. A glowing rim on concrete means pressure is too high or the wheel is finished.
Dust and Safety: Silica, Shroud and Kickback
Respirable crystalline silica is the fine fraction of concrete dust, and long-term exposure to it causes serious lung disease. It is the reason grinding concrete indoors without containment is a bad idea, and no grinder solves it on its own. A shroud and a HEPA vacuum capture dust at the source, and a P100 respirator covers what escapes.
Isolation and cleanup matter as much as capture. Seal off the work area, and clean up with a shop vacuum rather than a broom, because a broom simply puts the dust back in the air. People who work in basements and garages ask about this constantly, and the honest answer is that a shroud plus a vacuum changes the job from unpleasant to workable.
Kickback is the other concrete-specific hazard. It happens when a wheel catches an edge, a hidden rebar bar or a soft patch. Hold the grinder with two hands, keep the guard positioned between you and the wheel, start at a shallow angle, and let the machine’s brake or clutch do its job. Never grind a concrete edge by plunging the wheel into the corner at full speed.
For scale, masonry users describe concrete work as very loud, very messy but simple enough with the right setup. The technique that helps most is holding the cup wheel at about a 45 degree tilt and working in overlapping half-moon passes rather than grinding flat across the surface.
Frequently Asked Questions
What type of grinder is best for concrete?
A general 4-1/2 or 5 inch angle grinder with a diamond cup wheel handles most DIY concrete work, while a 7 inch paddle switch grinder suits heavy coating and stock removal. Large floor areas need a dedicated concrete surfacing or ride-on machine rather than a handheld.
What size angle grinder for grinding concrete?
A 4-1/2 inch grinder is the default for edges, joints and inside corners, and a 5 inch wheel covers more floor per pass for most jobs. Move to 7 inch for big slab work, where fewer passes matter more than low weight.
Can an angle grinder be used to grind concrete?
Yes. Any angle grinder with a spindle lock and adequate amperage can take a diamond cup wheel, and many 4-1/2 inch models are used for concrete every day. What changes between models is power, dust control and wheel coverage, not whether concrete is possible.
Which brand is considered the best for angle grinders?
Experienced tradespeople on weldingweb and sawmillcreek threads consistently name Metabo and Makita for longevity, and Milwaukee for comfort during extended grinding. DEWALT is widely treated as the value pick for power, and Bosch builds for dust-resistant construction work.
What is the best concrete grinding wheel for an angle grinder?
A diamond cup wheel is the correct abrasive. Choose double row for aggressive removal and single row for a finer finish, with 30-40 grit for stock removal and 60-80 grit for finishing passes. Never use a cut-off blade for surface grinding.
Final Verdict
The DEWALT DCG413B is our pick for most people in 2026, because its balance, brake and brushless motor make concrete work predictable without a cord in the way. The Makita 9557PBX1 is the one to buy if you want a sealed grinder that still works in five years, and the Metabo HPT G12SR4 covers edges and patching at the lowest outlay. Whichever you choose, budget for a diamond cup wheel, a dust shroud with a HEPA vacuum and a P100 respirator, because the consumables decide the job as much as the machine does.